Flat or Dead-Flat Oil - Provides a completely flat, oil-based finish. Generally used on walls but not suitable for areas of high wear. Note: How to use an airless paint sprayer. I'm sure the guy at the rental store showed you how to use the airless (typically with his limited experience of actually painting a house), so hopefully I can offer you a couple new ideas on how to paint your home using an airless paint sprayer. When you first get the airless home, set it in the middle of the area that you would like to start painting. Typically the length of the hose is around 50'. Stretch out the hose prior to painting so that you don't have to worry about unraveling it while you are painting on a ladder. It is a good idea to have a 100' extension cord so that you can bring the airless anywhere you wish to paint without any restrictions. Tip: before you plug in the airless into the extension cord, MAKE SURE THE AIRLESS IS OFF! You don't want the airless to start pumping without paint! Now, when you go to set up the airless, before you turn it on, it's a good rule of thumb to have a second empty bucket next to your bucket of paint. I'll explain why in a second. Place both buckets side by side and place the intake hose (with the wire mesh filter end) into your 5 gallon bucket of paint while the primer hose (usually a lot smaller, about the size of a pencil'ish) is placed in the empty bucket of paint. Before you turn on the machine make sure that the airless is set to prime the machine first. There is a primer valve that you can rotate between prime and paint. A good way to see if the valve is set to prime or paint is to try this little test prior to turning the machine on. While turning the valve clockwise a couple times you will notice that the valve handle will separate from the machine in one position (leaving a slight crack between the valve and machine) while the other position the valve is close to the machine. The position in which the valve is separated from the machine is considered the primer position. Do this multiple times to see what I'm talking about. Don't worry if you keep on spinning the valve, you can spin it a million times in one direction and it won't hurt it. Emotional: I think every parent wants their child to be emotionally contented and stable, to have a strong sense of self worth and self esteem. Imaginative play gives children the opportunity to work through aspects of their lives they are struggling with. It allows them the space in which to examine and change and minimize consequences of their own actions and experiment with different end results to situations. This playing helps children "work through" difficult emotional situations and to develop positive coping strategies.
Proper brush technique: When "cutting in" with a paint brush you should dip the brush in paint and tap the sides of the bucket on each side of the brush, leaving a good amount on the brush so you are able to minimize the times you will need to dip/load the brush. Next, take the brush and make a one foot to two foot line down the wall about an inch or two away from the trim or surface you are going to paint up next to, this is much like taking a knife full of butter and spreading it across an entire slice of bread. After, spreading the paint over the section, go back and even the paint out evenly across the section and cut up next to the trim with the brush. You want to paint up next to the trim or surfaced to be cut-in with the paint brush after you have released most of the paint on the wall, it is easier to cut in with the tips of the brush exposed and not loaded with a lot of paint. SECONDARY COLORS. When you mix two primary colors together, you get a secondary color. The secondary colors are orange, green and violet. Orange is made by mixing red with yellow. Green is made by mixing blue and yellow. Violet is made my mixing blue with red. And if you are changing colors be sure you and the paint shop are crystal clear on what color they're going to spray. Never just describe the color. You won't get what you want. Guaranteed. If you're not using a factory original color then find out what kind of car the color you want came on. Give the shop a year, model and paint name and then insist on seeing a paint chip. Take the chip outside to see it in the sun light and verify that it's what you want. There's nothing more disappointing then spending all these hours and money only to watch your car come out of the shop the wrong color. Purchase paint pan liners 5 for about $5. Once your done simply throw the liner out saving your paint pan and also giving you the opportunity to change paint colors without having to clean and dry the pan.