When spraying your house, it is a good rule of thumb to spray in the direction of the grain of the material. So if you have siding that runs horizontal, you want to spray in a horizontal style. Also, when you go to spray, the gun should be approximately 12" from the material that you are spraying. Do not pull the handle to spray with your hand still. This will spray a lot of paint in one spot causing it to drip. So have your hand moving when you go to depress the handle. This will give you an even look to your paint. Note: How to use an airless paint sprayer. I'm sure the guy at the rental store showed you how to use the airless (typically with his limited experience of actually painting a house), so hopefully I can offer you a couple new ideas on how to paint your home using an airless paint sprayer. When you first get the airless home, set it in the middle of the area that you would like to start painting. Typically the length of the hose is around 50'. Stretch out the hose prior to painting so that you don't have to worry about unraveling it while you are painting on a ladder. It is a good idea to have a 100' extension cord so that you can bring the airless anywhere you wish to paint without any restrictions. Tip: before you plug in the airless into the extension cord, MAKE SURE THE AIRLESS IS OFF! You don't want the airless to start pumping without paint! Now, when you go to set up the airless, before you turn it on, it's a good rule of thumb to have a second empty bucket next to your bucket of paint. I'll explain why in a second. Place both buckets side by side and place the intake hose (with the wire mesh filter end) into your 5 gallon bucket of paint while the primer hose (usually a lot smaller, about the size of a pencil'ish) is placed in the empty bucket of paint. Before you turn on the machine make sure that the airless is set to prime the machine first. There is a primer valve that you can rotate between prime and paint. A good way to see if the valve is set to prime or paint is to try this little test prior to turning the machine on. While turning the valve clockwise a couple times you will notice that the valve handle will separate from the machine in one position (leaving a slight crack between the valve and machine) while the other position the valve is close to the machine. The position in which the valve is separated from the machine is considered the primer position. Do this multiple times to see what I'm talking about. Don't worry if you keep on spinning the valve, you can spin it a million times in one direction and it won't hurt it. In this section are some tips on techniques and tools that make it easier to paint your house than ever before - not the way the "pro" does, perhaps, but with much the same results.
Before you start painting, it is a good idea to keep an eye on the weather for rain or snow. You don't want to start painting only to stop abruptly because of the weather. Take off the chrome molding around both the windshield and rear window. You can pick up a special tool at your local Mustang shop or by mail order that removes these quickly without scratching paint. Of course your paint is probably not in great shape at the moment, so a large flat screw driver will also do the trick. For some classic cars it makes sense to even remove the windshield, but classic Mustangs have chrome molding that will help cover any slight overspray. How warm does it have to be in order to paint your home? For most paints it typically has to be 37 degrees or warmer in order to paint the exterior of your house. Now if you are painting two coats of paint on your house and it is 55 degrees or cooler for the day, it is a good idea to paint the first coat one day and apply the second coat the day after. If you live in a really dry climate, like Denver, and your painting in the summer months, you can defiantly apply two coats in one day. However, the more humid climates in the south, it is still recommended to paint only one coat per day. Specialist paints also include some exciting new finishes, such as suede effects, metallics and high-sheen lacquers. Judy Smith, colour consultant at Crown, suggests an accent wall in one of these to lift a neutral scheme. Crown's Feature Wall range, which includes eight metallic finishes, nine bright colours and a highly reflective Pure Brilliant White, comes in convenient 1.25 litre tins.