Wood Walls and Trim. New interior walls and wood trim should be smoothed with sand-paper and dusted before painting or varnishing. To preserve the grain of the wood, the surface may be rubbed with linseed oil, varnished or shellacked, and waxed. If an opaque finish is desired, semi-gloss paint thinned with 1 pint of turpen-tine per gallon of paint or the primer-sealer previously described for walls may be used as a priming coat on wood. One or two coats of semi-gloss paint should then be applied over the thoroughly dry prime coat, or if a full-gloss finish is desired, the last coat should be a high-gloss enamel. Note: How to use an airless paint sprayer. I'm sure the guy at the rental store showed you how to use the airless (typically with his limited experience of actually painting a house), so hopefully I can offer you a couple new ideas on how to paint your home using an airless paint sprayer. When you first get the airless home, set it in the middle of the area that you would like to start painting. Typically the length of the hose is around 50'. Stretch out the hose prior to painting so that you don't have to worry about unraveling it while you are painting on a ladder. It is a good idea to have a 100' extension cord so that you can bring the airless anywhere you wish to paint without any restrictions. Tip: before you plug in the airless into the extension cord, MAKE SURE THE AIRLESS IS OFF! You don't want the airless to start pumping without paint! Now, when you go to set up the airless, before you turn it on, it's a good rule of thumb to have a second empty bucket next to your bucket of paint. I'll explain why in a second. Place both buckets side by side and place the intake hose (with the wire mesh filter end) into your 5 gallon bucket of paint while the primer hose (usually a lot smaller, about the size of a pencil'ish) is placed in the empty bucket of paint. Before you turn on the machine make sure that the airless is set to prime the machine first. There is a primer valve that you can rotate between prime and paint. A good way to see if the valve is set to prime or paint is to try this little test prior to turning the machine on. While turning the valve clockwise a couple times you will notice that the valve handle will separate from the machine in one position (leaving a slight crack between the valve and machine) while the other position the valve is close to the machine. The position in which the valve is separated from the machine is considered the primer position. Do this multiple times to see what I'm talking about. Don't worry if you keep on spinning the valve, you can spin it a million times in one direction and it won't hurt it. When choosing colours for exterior surfaces, consider the style of the brickwork or masonry of your home along with the colours used on nearby buildings, so as to pick colours that are sympathetic to these surroundings. Colours for fences and sheds should be selected with the same criteria in mind.
Materials and their application, every paint manufacturers paint will vary. If you are freshening up old walls and painting back to the existing color, the product doesn't have to be high end or have good coverage. If you need to paint a dark color over light color or light color over dark, you may want to consider purchasing a top quality paint to avoid multiple coats. I suggest Valspar, Pittsburgh or Benjamin Moore top of the line wall paint. These brands work well for straight out of the bucket use and are application friendly. Sherwin Williams is not my first choice because the coverage is poor and you will have to apply multiple coats but, it does apply, fluently. If you find a product does not apply well, maybe it is to heavy and/or sagging on the wall, you may need to thin the paint with a little water, this will reduce the coverage but make the paint flow better and lay down nicer on the surface. I do recommend latex paints for all applications, these days a good high end latex is as good as oil paint and your tools clean up much easier, it will also be less harsh on the respiratory system. The only situation I recommend oil paint, is as a primer/stain blocker over stains that "bleed" through the paint. You can get a stain blocking oil primer in a convenient spray can and spot prime any trouble areas before painting and in the case you need to prime all of the wall due to smoke or water damage, I recommend getting it in gallons and rolling it on where the stains are present. Don't forget proper ventilation and/or a respirator when using the oil based primers! White color symbolizes the purity, immaculateness, innocence, virtue, and joy. It always inspires, helps, fills you with faith. White means absolute freedom from obstacles and freedom for all possibilities. The perspective. Do you feel the distance between you and the painting? Are you an observer or a participant? The way you feel is dictated by the artistic choice - it's never a coincidence. An artist thoroughly selected the angle: you may look upwards, or downwards, or be at the same level with the objects depicted. If the horizon is at your eye level, the impression you will get is calm, stable. The high horizon will reveal more space, in landscapes it provides a majestic view. Paintings with the low horizon, so common with Dali, are monumental, highlighting the size of the objects and figures. The unusual views of Paris by Pissarro appeared as he painted from the hotel rooms. Vinyl is a cousin to the tough plastic used for upholstery and floor tiles, but it comes thinned with water ready for you to brush, roll or spray on. The label on the can may say vinyl, vinyl emulsion, polyvinyl acetate or PVA.